USB-BT Transparent Bridge (No IP Translation Solution)

Source code path: example/cherryusb/host/usb_bt_bridge_l2

Overview

This example implements a USB-BT transparent bridge. The Dongle forwards Ethernet frames received on USB RNDIS and Bluetooth PAN/BNEP directly to each other, completely bypassing the lwIP IP layer. There is no routing or NAT, and the Dongle itself does not take part in the IP stack. The earbud gets an address in the same subnet as the phone’s USB network and lives on the same L2/L3 network as the phone.

Unlike the NAT solution (example/cherryusb/host/usb_bt_bridge_nat, lwIP NAT), the Dongle here has no IP and does not go online by itself; it acts as a pure transparent pipe.

Supported Boards

Verified on the following development boards:

sf32lb52 LCD series

Hardware Required

A SiFli development board with USB Host support
USB Type-C cable
A HarmonyOS/Android phone (with “USB tethering” support)
A Bluetooth PAN (PANU) earbud

Technical Principle

Transparent Forwarding Path

Earbud PANU (10.196.255.x)
    │
    │ DHCP Discover
    ▼
BT PAN / BNEP ──► Dongle direct forward ──► USB RNDIS ──► Phone DHCP Server
The phone replies with DHCP Offer / ACK.
These replies travel back along the reverse path to the earbud

When forwarding succeeds, the earbud gets an address in the same subnet as the phone’s USB network, e.g.:

Phone gateway: 10.196.255.57
Earbud address: 10.196.255.x

Because the earbud and the phone are on the same IP network, the following are no longer needed:

IPv4 forwarding (IP_FORWARD)
NAT
DHCP Server on the Dongle’s b0
DHCP Client on the Dongle’s u2
lwIP IP-layer routing

Note: u2/b0 are lwIP interface names (the netdev names shown by ifconfig), not USB/Bluetooth spec terms: u2 is the USB RNDIS netif and b0 is the Bluetooth PAN/BNEP netif.

Weak Hook Mechanism (Core)

The CherryUSB Kconfig option PKG_CHERRYUSB_HOST_CDC_RNDIS_NO_NETIF (C macro USBHOST_RNDIS_NO_NETIF) decides whether a frame goes through the bridge:

Bridge mode (macro on): the u2 netif is not registered, and every frame received over USB goes directly to the hook usbh_rndis_on_raw_rx() — lwIP is never touched.
Non-bridge mode (macro off): the u2 netif is registered normally and frames take the normal lwIP netif path (the hook is not called).
USB → BT: external/cherryusb/class/wireless/usbh_rndis.c defines the weak function usbh_rndis_on_raw_rx(buf, len); this project overrides it in main.c: when a PAN connection exists (s_pan_bnep_id is valid), it calls bt_pan_send_data(s_pan_bnep_id, buf, len) to send the USB frame to the earbud over the BNEP channel.
BT → USB: middleware/bluetooth/service/bt/bt_finsh/bts2_app_pan.c defines the weak function bt_pan_on_raw_rx(buff, len); this project overrides it in main.c: it takes the RNDIS TX buffer via usbh_rndis_get_eth_txbuf(), memcpys the frame, and sends it via usbh_rndis_eth_output().

Key Configurations

PKG_CHERRYUSB_HOST_CDC_RNDIS_NO_NETIF (provided by CherryUSB, enabled by this project): the lwIP netif u2 is not registered after RNDIS enumeration; the RNDIS driver itself tracks the link state (usbh_rndis_is_link_up()), so the Dongle never touches lwIP.
BT_PAN_NO_B0_NETIF (provided by the Bluetooth component, enabled by this project): the lwIP netif b0 is not created on PAN connect; received frames are handed to the application hook bt_pan_on_raw_rx().

Limitations

The Dongle has no IP and cannot go online locally (e.g. ping).

Using the Example

Compile and Flash

Change to the example project directory and run scons to compile:

scons --board=sf32lb52-lcd_a128r16 -j8

Run the flash command:

build_sf32lb52-lcd_a128r16_hcpu\uart_download.bat

Select the serial port as prompted to download:

please input the serial port num:6

Earbud Side

You can use another development board as the earbud side. For the earbud firmware, use the example\bt\pan example and flash it into the second board using the same compile/flash procedure above for testing.

Usage Steps

Flash the firmware, connect the phone via USB and enable “USB tethering”
Observe [USB] RNDIS link up, USB<->BT bridge active
Flash the earbud-side firmware and power it on
On the Dongle, start the inquiry: pan_net inquiry start
On the Dongle, connect: pan_net conn <earbud MAC> (e.g. pan_net conn 12345678abcd)
After the Bluetooth connection is established, the earbud should obtain an IP in the same subnet as the phone network (e.g. 10.196.255.x) and be able to access the Internet; verify with ping 8.8.8.8.

Example Output

TX:ping 8.8.8.8
   D/BT.lwip bts: rt_bt_lwip_protocol_recv netif 0x20037094
   D/NO_TAG bts: Active mode st: 0, inv: 0.00
   D/btapp_pan bts:  BTS2MU_PAN_STS_IND
   D/BT.lwip bts: rt_bt_lwip_protocol_recv netif 0x20037094
   60 bytes from 8.8.8.8 icmp_seq=0 ttl=106 time=901 ms
   D/BT.lwip bts: rt_bt_lwip_protocol_recv netif 0x20037094
   60 bytes from 8.8.8.8 icmp_seq=1 ttl=106 time=283 ms
   D/BT.lwip bts: rt_bt_lwip_protocol_recv netif 0x20037094
   60 bytes from 8.8.8.8 icmp_seq=2 ttl=106 time=286 ms
   D/BT.lwip bts: rt_bt_lwip_protocol_recv netif 0x20037094
   60 bytes from 8.8.8.8 icmp_seq=3 ttl=106 time=284 ms
   msh />msh />

Troubleshooting

Dongle does not respond when connected to the phone: make sure the USB cable supports data transfer.
CherryUSB